BMW 7_aya the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and methods of operation
3. Settings and routine maintenance of the car
4. Engine
5. Cooling systems of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Cardan and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
13.1. External equipment and body elements
13.1.1. Removal and installation of a forward wing
13.1.2. Removal, installation and adjustment of doors
13.1.3. Removal, installation and adjustment of a cowl, replacement of its racks
13.1.4. Removal, installation and adjustment of a cover of the luggage compartment, replacement of its components
13.1.5. Removal and installation of a front bumper and its components
13.1.6. Removal and installation of a rear bumper and its components
13.1.7. Replacement and adjustment of mobile glasses of doors
13.2. Equipment of salon
14. Onboard electric equipment
15. Schemes of electric equipment




13-1-2-snyatie-ustanovka-i-regulirovka-dverejj.html

13.1.2. Removal, installation and adjustment of doors

Removal and installation

Forward and back doors are removed equally.


 PERFORMANCE ORDER

  1. Turn out bolts with a six-sided head above and below.
  1. Remove a protective cover. If the bracket is established, remove it. Install adaptation No. 51 2 010 and beat out a loop axis up.

At installation for driving in of a loop install adaptation No. 51 2 010 from above.

  1. Raise a door, take out it from a loop and lower on in advance prepared support about a threshold so that not to load a door electrical wiring.
  1. Turn out two screws of fastening of the socket of an electrical wiring. Extend the socket from a forward rack and separate it.
  1. Installation is made upside-down.
1 — the Bolt with a six-sided head
2 — the Motionless link of the top loop, fastens to a body
3 — a loop Axis
4 — the Mobile link of the top loop with the hinge plug, fastens to a door
5 — the Washer
6 — the Lock washer

Adjustment

Before adjustment of forward doors it is necessary to adjust back doors, i.e. back doors are adjusted to the welded back wings. In this case forward wings which fasten bolts if necessary it is possible to adjust to forward doors. At adjustment the door has to be completed with glass and the mechanism of a window regulator.

Sizes of gaps are specified in Specifications of the Head Kuzov.


 PERFORMANCE ORDER

  1. Weaken fastening of the drummer of the lock.
  2. Completely remove tubular consolidation of a forward door.
  3. At installation of new doors establish expansion washers between a door and loops. For preliminary adjustment establish two washers, each 1 mm thick. Adjust a gap by means of the corresponding quantity of washers of necessary thickness.
  4. Lower glasses. At installation of new doors carry out preliminary adjustment of their situation on height: without the lower dustproof overlay of a door the size of the lower gap on all length has to make about 20 mm. Adjustment is carried out by means of movement of loops.
  5. Check and if necessary adjust forward and back gaps (on a back door – only back) – they have to be uniform and make 5 mm. Adjustment is carried out by means of movement of loops.
  6. At adjustment of a back door check its situation on height concerning a body. At adjustment of a forward door check the mutually provision of forward and back doors on height. If necessary adjust the corresponding door on height as it is described below.
  1. Insert a template No. 51 2 090 into the door lock.
  1. Weaken the screw (1). To weaken the screw (2) so that the drummer of the lock could be shifted by insignificant effort of a hand.

Do not change adjustment of a clamp on depth (3).

  1. Raise the handle of a door and, holding it in this situation, close a door. Height and an inclination of the drummer of the lock is regulated on a template. Open a door and tighten screws (1 and 2 on an illustration).
  2. Check tubular consolidation of a door for absence of damage and if necessary replace it. To establish tubular consolidation of a door.
  3. Establish the lower dustproof overlay for a door.
  4. At installation of a forward door check a print of tubular consolidation for the door surfaces interfaced to it. For this purpose, being in the car at the closed door, insert thin (no more than 1 mm) a rectangular plastic subject (for example, the credit card) between tubular consolidation and a frame of a door and carry out this subject along the interfaced surface of consolidation and a frame, checking prilegany consolidations. In a ceiling zone between forward and central racks of a body the subject serving for check should not be extended easily. If necessary replace consolidation or align a door fold which consolidation is put on.

The excessive rikhtovka of a fold will lead to increase in the effort necessary for closing of a door.



"previous page
13.1.1. Removal and installation of a forward wing
following page"
13.1.3. Removal, installation and adjustment of a cowl, replacement of its racks