|
|
|
12-2-8-snyatie-i-ustanovka-razborka-i-sborka-stojjki-podveski.html
12.2.8. Removal and installation, dismantling and assembly of a rack of a suspension bracketRemoval and installation
|
|
- Remove a support of the brake mechanism, without disconnecting a brake hose, and suspend it on a body (see the Head the Brake system).
|
|
- Give a nut and a vypressuyta cross steering draft by means of a stripper No. 32 1 190.
|
|
|
At installation on a landing cone and in an opening there should not be lubricant traces; use new самоконтрящуюся a nut. |
|
|
- Disconnect a rack of the stabilizer of cross stability from a suspension bracket rack, holding fixing knot from a provorachivaniye a wrench. Bring a cable out of a fastening arm to a rack to a suspension bracket.
|
|
|
At installation use new самоконтрящуюся a nut. |
|
|
- Turn out a bolt, install adaptation No. 31 2 200 in a cut and turn on a corner 90 °. Leave adaptation on a rotary fist before installation.
|
|
|
|
|
At installation the bolt has to enter an opening of a plate (1). |
|
|
|
- Remove a cap of the top support of a rack of a suspension bracket. At the corresponding complete set separate the EDC system socket. Give the top nuts of fastening of a rack.
|
- Press on a rotary fist with the cross lever of a suspension bracket and an extension of the lever of a suspension bracket so that it was possible to take out a rack from a wheel arch. Disconnect a rack from a rotary fist.
|
|
Do not allow damage of a wheel arch, it is necessary to remove a rack together. |
|
|
Dismantling and assembly
|
|
It is not allowed to use pulse винтоверт for tightening and unclamping of adaptation No. 31 3 341, and also for a reversing of bolts of fastening of the top support of a rack to a rack cylinder rod! |
Components of assembly are resistant suspension brackets
|
|
|
|
- Clamp the plug (1) of adaptation No. 31 3 141 in a vice. Lock pins (2) have to be recorded with the heard click and with feeling of the moment of fixing. Double-check fastening of devices (horns) No. 31 352.
|
|
|
It is necessary to check operability of devices before each their use. Do not use the damaged devices and do not change their design. Use only suitable horns established from a facet of adaptation No. 31 3 141. |
|
|
- Establish a spring between horns so that its lower end (1) was under a horn and was coaxial to its end (2), and between horns there were 3 rounds of a spring.
|
|
|
At compression rounds of a spring have to enter deepenings of horns completely. Squeeze a spring only before removal of effort from the top support of a rack of a suspension bracket (not to a prileganiye of rounds of a spring to each other). |
|
|
- Holding knot from a provorachivaniye a cap wrench, give a nut by means of special adaptation No. 31 2 210 or a key on 24 mm.
|
|
|
It is allowed to give a nut only if both rounds of a spring completely are in deepenings of horns. |
- Remove a suspension bracket rack.
- At installation of a new spring unclench adaptation No. 31 3 341, remove an old spring and squeeze new according to the requirements described in paragraph 2.
- Check a corrugated casing, a chipper and the isolating laying of a spring and if necessary replace faulty details.
- Installation is made upside-down. The ends of a spring have to coincide with step pimples of plates. Use new самоконтрящуюся a nut of fastening of a spring.
|
|
It is not allowed to unclench adaptation to a contact of horns of the lower plate of a spring and the top round of a spring or the top support of a rack. Otherwise damage of adaptation or a spring is possible. Unclench adaptation only before removal of effort of compression from spring rounds. |
|
|
|
|
|