Removal and installation of steering drafts, bipod and pendular lever. BMW the 7th E38 series (from 1994 to 2002 release)
 
BMW 7_aya the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and methods of operation
3. Settings and routine maintenance of the car
4. Engine
5. Cooling systems of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Cardan and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
12.1. General information, recommendations and security measures
12.2. Forward suspension bracket
12.3. Back suspension bracket
12.4. EDC system
12.5. Steering
12.5.1. Principle of work of GUR
12.5.2. Removal and installation of a steering wheel, block of a safety cushion and its contact ring
12.5.3. Removal and installation of casings of a steering column
12.5.4. Removal and installation of assembly of a steering column and sensor of an angle of rotation
12.5.5. Replacement of the lever of adjustment of a steering column
12.5.6. Removal and installation of the lock of ignition and blocking of a steering wheel
12.5.7. Removal and installation of the steering mechanism from GUR
12.5.8. Removal and installation of steering drafts, bipod and pendular lever
12.5.9. Removal and installation of the pump GUR
12.5.10. The angles of installation of wheels of the car - the general information
13. Body
14. Onboard electric equipment
15. Schemes of electric equipment



12-5-8-snyatie-i-ustanovka-rulevykh-tyag-soshki-i-mayatnikovogo-rychaga.html

12.5.8. Removal and installation of steering drafts, bipod and pendular lever

Bipod

When replacing a bipod of steering it is necessary to check height of its installation in relation to the pendular lever.


 PERFORMANCE ORDER

  1. Remove the steering mechanism (see the Section Removal and installation of the steering mechanism from GUR).
  2. Turn out tightening the screw (1), previously having noted the provision of an adjustable bipod of steering on a shaft with the gear sector.
1 — Tightening the screw
2 — Tags
  1. Installation is made upside-down. Spread a steering bipod to the put tag. At the same time the tag (2) has to be a steering bipod vent in the middle.

Replace самоконтрящуюся a nut.

Cross steering drafts

 PERFORMANCE ORDER

  1. To turn off a nut and to remove cross steering draft by means of adaptation No. 32 1 190.

At installation on a pin and in an opening there should not be lubricant traces. Replace самоконтрящуюся a nut. If necessary hold knot from a provorachivaniye for an internal hexagon.


  1. Weaken tightening a bolt and turn out cross steering draft.
  1. Installation is made upside-down. Completely grease the adjusting coupling of draft with special lubricant.
  2. Upon termination of works check and adjust the angles of installation of forward wheels.

Average draft

 PERFORMANCE ORDER

  1. To remove protection of a case of the engine.
  2. Give a nut and disconnect draft from a bipod of steering and from the pendular lever by means of a stripper No. 32 1 190.

At installation replace самоконтрящуюся a nut. If necessary hold knot from a provorachivaniye for an internal hexagon.

  1. Weaken the left and right tightening bolts (see an illustration) and turn out the adjusting coupling of draft at the left and on the right.
  2. Measure depth of installation of the adjusting coupling on the ends of old draft and screw the adjusting coupling on new draft on the corresponding depth on both sides.
  3. Installation is made upside-down. Grease the adjusting coupling of draft with special lubricant.
  4. Upon termination of works check and adjust the angles of installation of forward wheels.

Pendular lever

Details of knot of fastening of the pendular lever
1 — the Bolt
2 — the Pendular lever
3, 4 — Samokontryashchayasya a nut
5 — the Beam of the forward bridge

After replacement of the pendular lever it is necessary to adjust a steering bipod.


 PERFORMANCE ORDER

  1. Remove protection of a case of the engine.
  1. Give a nut and disconnect a spherical support by means of a stripper No. 32 1 190.

At installation on a pin and in an opening there should not be lubricant traces. Replace самоконтрящуюся a nut. If necessary hold knot from a provorachivaniye for an internal hexagon.



"previous page
12.5.7. Removal and installation of the steering mechanism from GUR
following page"
12.5.9. Removal and installation of the pump GUR