BMW 7_aya the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and methods of operation
3. Settings and routine maintenance of the car
4. Engine
5. Cooling systems of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Cardan and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
13.1. External equipment and body elements
13.2. Equipment of salon
13.2.1. Removal and installation of window regulators
13.2.2. Removal and installation of finishing and sound insulation of a forward door
13.2.3. Removal and installation of finishing and sound insulation of a back door
13.2.4. Removal and installation of panels of finishing of racks of a body and ceiling
13.2.5. Removal and installation of finishing of the dashboard
13.2.6. Removal and installation of the shelf behind a back seat and blinds of back glass
13.2.7. Removal and installation of overlays of thresholds of doors
13.2.8. Removal and installation of elements of finishing of the luggage compartment and its cover
13.2.9. Removal and installation of front seats
13.2.10. Removal and installation of a back seat
13.2.11. Removal and installation of seat belts
13.2.12. Removal and installation of a cover of the top hatch
14. Onboard electric equipment
15. Schemes of electric equipment




13-2-3-snyatie-i-ustanovka-otdelki-i-zvukoizolyacii-zadnejj-dveri.html

13.2.3. Removal and installation of finishing and sound insulation of a back door

Finishing

 PERFORMANCE ORDER

  1. Remove a cap (1), release a clamp and remove the button (2) the movement up.
  1. At a complete set sun-protection blinds on side glasses unhook a blind (1) above and remove the movement (2) back and up.
  1. At a complete set sun-protection blinds on side glasses turn out the screw.
  1. Remove the lighting lamp of a foot well and the switch of a window regulator. Separate both sockets. Remove a cap (1) and turn out the screw.
  1. Release the panel of finishing of a door from clamps on all its perimeter, extend the finishing panel from clips the movement up and push the internal handle of the drive of the lock of a door via the finishing panel.
  1. Remove clips.
  1. Remove internal lower consolidation of glass of a door by the movement up.
  2. Installation is made upside-down. Pay attention to the next moments:
  3. Replace the damaged clamps.
  4. At a complete set sun-protection blinds on side glasses before installation of the panel of finishing of a door delay a curtain up and check serviceability of its functioning.
  1. Check distance (A = 14.5 ± 1 mm) between a cap (1) and a guide (2). If necessary remove the button and adjust position of the plug (3).

Sound insulation

 PERFORMANCE ORDER

  1. Remove facing of a back door.
  2. On models with a side safety cushion remove it.
  1. Separate the socket (1), turn out screws (2) and remove loudspeaker knot. Remove the handle of the drive of the lock of a back door.
  1. Disconnect the central light source (1) from an arm (2), separate the socket (3) and disconnect optical fiber (4) from the central light source.

Radius of a bend of optical fiber should not be less than 20 mm.


  1. Turn out screws (1) and remove an arm of the central light source (2).
  1. Unclench collars (1) on a plait of an electrical wiring (2) and on a cable (3), separate sockets (4).
  1. Take clamps (1 and 2), turn out the screw (3) and unhook a cable (4).
  1. Take clamps.
  1. In whole or in part separate the sealing roller (1) and remove or unbend sound insulation (2).
  1. Clear the interfaced surfaces and lay a butyl cord with a diameter of 6 mm on sound insulation and a door, heat it the technical hair dryer, impose sound insulation and strongly press it on all perimeter with effort of 30 N/cm2.
  2. Further installation is made upside-down.


"previous page
13.2.2. Removal and installation of finishing and sound insulation of a forward door
following page"
13.2.4. Removal and installation of panels of finishing of racks of a body and ceiling