BMW 7_aya the E38 series from 1994 to 2002
1. Introduction
2. Governing bodies and methods of operation
3. Settings and routine maintenance of the car
4. Engine
5. Cooling systems of the engine, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Manual box of gear shifting and coupling
9. Automatic transmission
10. Cardan and power shafts, reducer, differential and stupichny assemblies
11. Brake system
12. Suspension bracket and steering
13. Body
13.1. External equipment and body elements
13.2. Equipment of salon
13.2.1. Removal and installation of window regulators
13.2.2. Removal and installation of finishing and sound insulation of a forward door
13.2.3. Removal and installation of finishing and sound insulation of a back door
13.2.4. Removal and installation of panels of finishing of racks of a body and ceiling
13.2.5. Removal and installation of finishing of the dashboard
13.2.6. Removal and installation of the shelf behind a back seat and blinds of back glass
13.2.7. Removal and installation of overlays of thresholds of doors
13.2.8. Removal and installation of elements of finishing of the luggage compartment and its cover
13.2.9. Removal and installation of front seats
13.2.10. Removal and installation of a back seat
13.2.11. Removal and installation of seat belts
13.2.12. Removal and installation of a cover of the top hatch
14. Onboard electric equipment
15. Schemes of electric equipment




13-2-5-snyatie-i-ustanovka-otdelki-paneli-priborov.html

13.2.5. Removal and installation of finishing of the dashboard

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the rechargeable battery.
  2. Remove finishing of forward racks (see the Section Removal and installation of panels of finishing of racks of a body and ceiling).
  3. Remove a combination of devices (see the Head Onboard electric equipment).
  4. Remove a safety cushion of the forward passenger.
  1. Release a clamp (1) and separate the socket (2). Turn out bolts and remove holders (3 and 4) of a safety cushion of the forward passenger.
  1. Turn out screws.
  1. To turn out the top plastic nuts and remove a wooden level (1). In addition give a plastic nut on the left side of a level (2).

It is necessary to establish extreme plastic nuts by a nakatka to a level, and the central nuts – a hexagon to a level.


  1. Turn out screws (1 and 3) and uncover a ware box (2) and an angular part of finishing (4) by the movement on yourself.
  1. Turn out bolts (1 and 2).
  1. Wring out clamps and remove a wooden level (1), if necessary having separated the socket of a tempostat. Wring out clamps, remove a wooden level (2) and separate the socket. Take out sockets of an electrical wiring of switches of lighting (3).

At installation replace the damaged clamps and caps.


  1. Turn out bolts (1).
 
  1. Turn out top (without pro-masonry washer) and lower (with a pro-masonry washer) bolts, remove the left ware box (1) and unhook a cable of an otpuskaniye of the parking brake.
  1. Turn out bolts under a steering column.
  1. Remove the central deflectors of the HVAC system (see the Head of the Cooling system of the engine, heating, ventilation and conditioning).
  1. Turn out bolts with left and on the right side and remove the dashboard the movement on yourself and up, shifting it towards the right forward door.
  1. Remove laying (1 and 2) forward parts of the dashboard and a heater.
  1. Installation is made upside-down. Pay attention to the next moments.
  2. Just before assembly of the dashboard to impose new laying of a forward part of the dashboard and a heater.
  1. Establish plastic guides (1) with left and on the right side and (2) on the center.


"previous page
13.2.4. Removal and installation of panels of finishing of racks of a body and ceiling
following page"
13.2.6. Removal and installation of the shelf behind a back seat and blinds of back glass